Du verwendest einen veralteten Browser. Es ist möglich, dass diese oder andere Websites nicht korrekt angezeigt werden. Du solltest ein Upgrade durchführen oder einen alternativen Browser verwenden.
Heute wurde ein weiterer neuer Brooks-Bass geboren!
Wie die meisten Brooks-Bassgitarren handelt es sich um ein Hybriddesign.
Der Brooks PB-2 vereint die Eigenschaften eines Gibson EB-2 und eines Fender Precision.
Specifications:
- Hollow Maple body with maple centre piece
- Flamed Maple with...
Heute wurde ein neuer Bass geboren.
Meine Damen und Herren, ich gebe Ihnen:
Der Brooks Nachtkrapp Airborne (Chris Laut Signature)
Chris Laut ist der Leadsänger/Bassist der deutschen Rockband Ohrenfeindt. Chris hat mich beauftragt, diesen Hybrid aus einem Non Reverse und einem Reverse...
Gibson hat den alten EB-0 von Gene Simmons in einer limitierten Auflage ausgebracht.
Egal ob man ein Kiss-Fan ist oder nicht, der Bass ist immer noch sehr schön (meiner Meinung nach)
Die 1959er EB-O mit Les Paul Junior Double Cut-Körperform wurde von Gene modifiziert. Er hatte den Mudbucker...
Yeeehaaaaw!
Der Brooks QB ist bereit.
Dieser Zwölfsaiter-Bass im 34" Mensur ist eine Hommage an den Quad Bass, den Jol Dantzig von Hamer 1978 für Tom Petersson baute.
Nur dass ich im Einbaupanel kein Mischpult verbaut habe, sondern zwei Effekte!
Ein großes Dankeschön an Bas Becu von BQ Music für...
Trommelwirbel....
Bitte begrüßen Sie den Brooks EXB-MS-10.
Ein speziell angefertigter 10-Saiter-Bass mit mehreren Mensuren.
Dies ist mit Sicherheit der ehrgeizigste Bau, den ich bisher gemacht habe.
Einfach weil es keine Referenz gibt. Soweit ich weiß, gibt es keinen anderen auf der Welt.
An...
Basvarken
Thema
brooks bass guitars
fanned frets
multi scale bass
ten string bass
Warum soll das ein drei Punkt Bridge sein?
Ich bin der Meinung, dass diese "Wide Travel" Brücke eine bessere Brücke ist als die Dreipunktbrücke. Der Steg hängt nicht lose hinter den Studs und die Sättel fallen beim Saitenwechsel nicht heraus...
Polished the finish. And cleaned up the fretboard.
Healed the two broken off corners of the pickguard.
Had to desolder the ground wire to be able to put it back in at the treble side bridge post. Which wasn't a bad idea because the old soldering looked really crappy anyway (see on...
The half moon washer in the truss rod cavity had gnawed its way into the neck. So I decided to fill up the compressed wood with some mahogany. I made a little matching "washer" of mahogany and glued it onto the original metal washer. By doing this I knew that the shape was exactly the same as...
Before glueing the neck back into the body I drilled the new (smaller ) tuner holes. First marked them off, then drilled a pilot hole for the 11mm drill. Then cleaned up the hole with a Dremel to the desired 12mm.
Did need to fix the tiny tear out of the drill at the G tuner.
Filled up the...
When the back of the headstock was sanded clean of the old lacquer, I kept going and did the neck too. Carefully sanding and scraping the old lacquer off. There were a lot of dings and gauges on the neck. I didn't try to sand them out. But I tried to raise the gauges with some steam before I did...
The truss rod cavity, and in particular the part near the nut needed some attention. The washer between the brass nut and the wood has gnawed its way into the wood and lifted a chip up.
The routed rectangle where the Badass bridge sat had to be filled.
First I plugged the three screw holes...